Home/Blog/Design and print
Design and print 7 min read

QR Code Size for Signs and Shop Windows: The Scanning Distance Rule

Short answer

A common rule of thumb is to make a QR code about one tenth as wide as the distance people will scan from. Two metres away needs a code of about 20 cm. Hang it at eye level, light it evenly, keep it dark on a light background, block reflections on glass and print a short web address underneath.

By QR Business Cards Editorial TeamPublished Updated

On a business card, the code is held in someone's hand. On a sign, people stand back. A code that scans perfectly from a card may be useless from across a pavement. This guide shows you how to size your profile QR code for signs, posters and shop windows, and how to place it so phones read it first time.

Why distance changes everything

A phone camera reads a QR code by telling its small squares, the modules, apart. The further away the phone is, the smaller each module looks on screen. At some point the camera can no longer separate them, and nothing happens. So the right size depends less on the sign and more on where people will stand.

The amount of data matters too. A code with more data has more, smaller modules. A dynamic profile code holds only a short address, so its modules stay large. That is one reason to use the same short profile code on a sign as on your card, rather than a long web address.

The 10:1 rule of thumb

A widely used rule of thumb in sign making is a ratio of about 10:1: the scanning distance should be no more than about ten times the code's width. Put the other way round, make the code about one tenth as wide as the distance.

This is a rule of thumb, not a standard. The QR code standard, ISO/IEC 18004:2024, defines how a code is built but does not set sizes for signs. Phone cameras, light and the code's density all shift the result. Use the rule to get close, then test.

Viewing distance vs suggested code width

Where people will standTypical settingSuggested code width
About 50 cmCounter card, menu stand, table tentAbout 5 cm
About 1 metrePoster beside a till, door stickerAbout 10 cm
About 2 metresShop window seen from the pavement edgeAbout 20 cm
About 3 metresPull-up banner, wall sign across a roomAbout 30 cm
About 5 metresLarge window graphic, stand back wallAbout 50 cm

Widths are for the code only, using the 10:1 rule of thumb. Add the four-module quiet zone, the plain margin the standard requires, on every side. When in doubt, go one size up. A code that is too big still scans; a code that is too small does not.

Placement height

Size is wasted if people cannot point a phone at the code comfortably.

  • Aim for eye to chest height for people standing. That is where a phone naturally sits when someone lifts it.
  • Avoid the very bottom of a window. People would have to crouch, and the code gets hidden by display stands or pavement clutter.
  • Avoid high corners. A code above head height is scanned at an angle, which makes it look narrower.
  • Keep it near the door or the main line of sight. People scan what they see while they are already paused.

On a counter or table, lay the code flat or tilt it slightly towards the customer.

Lighting

Cameras need light to see contrast. In a shop window, light changes all day.

  • By day, direct sun can wash out a code or cast hard shadows across it. A spot out of full sun reads more reliably.
  • At night, a window code is only useful if it is lit. Make sure your display lights reach it, without a bright hot spot on the code itself.
  • Backlit signs work well if the code is printed on an opaque layer, so light does not shine through the white areas unevenly.

Check the code in the light it will actually have: morning, afternoon and evening if you can.

Glass reflections and window decals

Glass is the hardest surface for a QR code. The camera sees the code, the reflection of the street and the dark shop behind, all at once.

  • Give the code a solid light background. A clear decal leaves the code floating on whatever is behind the glass, often a dark interior. Use a white backing so the code is dark on light.
  • Fit decals on the inside facing out to protect them from weather and scratching. If you do, the decal must be printed so the code reads the right way round from outside. Tell your printer it is for inside application.
  • Cut reflections by placing the code where the glass is shaded, such as under an awning, or by choosing a matte decal material.
  • Avoid tinted or patterned glass behind the code where you can. Tint lowers contrast.

Before you commit, stick a paper print to the inside of the glass and try it from the pavement on two phones.

Under every sign code, print the domain your profile opens on, in large enough type to read from the same distance. It helps in three ways:

  • Trust. People can see where the code goes before they scan.
  • Fallback. Someone whose camera will not scan can type it in.
  • Protection. If anyone sticks a fake code over yours, the printed domain will not match what their phone shows.

Public codes can be targets for tampered stickers. Check your signs from time to time. Our guide to QR code phishing and business cards explains what to look for.

Add a line that says what opens

A sign competes with everything else in the street. Say why someone should stop:

  • "Scan to save our contact"
  • "Scan for opening times and directions"
  • "Scan to book an appointment"
  • "Scan to see what is new"

Make the line true. If it promises bookings, your profile needs a booking calendar. On our profiles, bookings come with the Business Add-ons plan only.

Prepare the file for large print

A small image blown up to poster size turns soft at the edges. For signs, use a vector file of the code wherever possible, so it stays sharp at any size. If you only have a raster image, export it at the final printed size. Ask your printer not to resize, recolour or sharpen it. Our print file checklist covers file types, error correction and proof checks.

Test from where people stand

Testing is the step most people skip. Do it before the sign is printed in full, and again once it is up:

  1. Print the code at real size on paper.
  2. Fix it where the sign will go.
  3. Walk to the spot people will scan from, and a step further.
  4. Scan with an iPhone and an Android phone, in the light the sign will have.

If either phone struggles, make the code bigger, move it out of glare or improve its contrast. If customers ask how to scan, our guide on how to scan a QR code business card on iPhone or Android works for signs too.

The same code in other places

The code on your window can be the same one as on your business card, your boxes and your event stand. For smaller surfaces, see QR codes on packaging and product inserts. For banners, badges and slides, see QR codes for events, trade shows and badges.

Where our cards fit

Our QR code business cards come with a dynamic profile and a QR code that opens it. You can use the same profile on signs and windows, and edit it at any time without reprinting anything. More guides are on the blog.

Frequently asked questions

As a rule of thumb, about one tenth of the scanning distance. For two metres, that is about 20 cm wide, plus the quiet zone.

No. It is a rule of thumb used in sign making. The QR code standard does not set sign sizes, so always test.

Between chest and eye height for someone standing on the pavement, near the door or the main line of sight.

Usually reflections, a dark background behind clear glass, poor light at night or a code too small for the distance.

Yes. A short domain builds trust, gives a fallback and makes a fake sticker easier to spot.

Yes, if it is a dynamic profile code. Print it larger to suit the distance.

Related guides

View All
Design and print

QR Codes on Packaging and Product Inserts for Small Businesses

Put the profile QR code from your business card on boxes, labels, thank-you inserts and swing tags: suggested sizes per surface, curved containers, glossy and kraft finishes, and what the scan should open for a customer.

Scanning and sharing

QR Codes for Events, Trade Shows and Badges: A Practical Set-up

How to use your QR business card profile at events: codes on badges, stand graphics, slides and table cards, one profile or separate codes, capturing leads at the stand on the Business Add-ons plan, and following up within a day.

Design and print

QR Code Business Card Print Specifications: The Print File Checklist

The print-ready file, step by step: vector or raster, module and code size, error-correction level, quiet zone, colour, bleed and the proof and test scans to run before the full print run.

Ready to Upgrade Your Networking?

Get your premium QR business card and start making lasting first impressions.

Shop the Full Range