Home/Blog/Design and print
Design and print 8 min read

QR Code Business Card Print Specifications: The Print File Checklist

Short answer

Send the code as vector art (SVG, PDF or EPS), or as a raster at final size with sharp, whole-pixel modules. Keep a four-module quiet zone, print the code in solid black on light stock with nothing behind it, keep it inside the safe area, and scan a printed proof on at least three phones before the full run.

By QR Business Cards Editorial TeamPublished Updated

A QR code can look perfect in your design file and still fail on the printed card. The usual culprits are a blurry export, a code that is too small for its data, a margin that got trimmed, or a colour the press could not hold. This checklist covers the print-ready file itself. Work through it before you approve a proof.

1. Start with a vector file

A vector file describes the code as shapes. It stays sharp at any size, so every module keeps a hard, square edge. A raster file is a grid of pixels. Scale it up and the edges blur; compress it and stray pixels appear around the modules.

File typeKindSuitable for the QR code?Notes
SVGVectorYesScales to any size; check your printer accepts it
PDF with vector artVectorYes, usually the safest hand-offKeep the code as vector paths, not an embedded picture
EPSVectorYes, if your printer still takes itAn older format that some tools no longer open
PNGRasterOnly at final size, never enlargedLossless, so edges stay clean if pixels line up with modules
JPEGRasterAvoidCompression softens edges and adds noise around modules
ScreenshotRasterNoUnknown size, usually blurred and scaled

If your QR code generator offers SVG or PDF, use it. Place the code in your layout as vector art and export the whole card as a print PDF. If you are adding the code to a card you already print, our guide to adding a QR code to your existing business card design covers placement and the hand-off to your printer.

2. If you have to use a raster file

Sometimes the only file you have is a PNG. Then follow three rules:

  • Export at the exact printed size. Never enlarge a small image to fit.
  • Make each module a whole number of pixels. If one module is 7 pixels wide, every module should be 7 pixels wide. Turn off smoothing or anti-aliasing so the edges stay hard.
  • Match the resolution your printer asks for. As a reference, our online card designer recommends background images of 1012 × 638 pixels for a full card face. On a card of 85.6 × 54 mm, the ID-1 size in ISO/IEC 7810:2019, that works out at about 300 pixels per inch. Do not let the code area fall below the resolution of the rest of the card.

Never use a JPEG for the code. Even at high quality, compression leaves faint blocks around the modules that a camera can misread.

3. Module size and overall code size

The size that matters is the module, the single square that a camera reads. Barcode specialists call its width the X-dimension. The QR code standard, ISO/IEC 18004:2024, defines how modules make up a code, but it does not set a print size for business cards. Signs and posters follow a distance rule instead, covered in our guide to QR code size for signs and shop windows.

The closest published benchmark comes from GS1, the barcode standards body. Its General Specifications, release 26.0 (2026), allow QR codes scanned at retail tills a module size from 0.396 mm to 0.990 mm, as GS1 UK explains. GS1 UK's design guidelines give 0.495 mm as the target. Those figures are for products at a till, not cards in a hand, but they are a sensible floor.

The number of modules depends on how much data the code holds. We encoded three samples at error-correction level M with an open-source encoder. Then we applied the GS1 module sizes, adding the four-module quiet zone on each side:

What the code holdsDataModules acrossTotal width at 0.396 mmTotal width at 0.495 mm
A short profile link32 bytes2914.7 mm18.3 mm
A basic contact card (name, mobile, email)112 bytes4521.0 mm26.2 mm
A full contact card (plus company, title, office line, website, address)317 bytes6930.5 mm38.1 mm

A business card is 54 mm tall. A short dynamic link fits comfortably at a generous size. A full contact block eats most of the card. Our guide to QR code design: size, contrast and quiet zone explains why simpler codes scan better.

4. Choose the error-correction level

Every QR code carries extra data that lets a camera rebuild damaged parts. ISO/IEC 18004:2024 defines four levels: L, M, Q and H. They can restore roughly 7, 15, 25 and 30 per cent of the code. More correction means more modules for the same data. Our short link needed 25 modules across at level L, 29 at M and Q, and 33 at H.

Which to use:

  • M for most cards printed on smooth stock. It balances size and safety.
  • Q for textured or engraved surfaces, or cards that will see a lot of wear.
  • H only if you place a small logo in the centre, because the logo covers modules the code must rebuild. Our guide to adding a logo and brand colours to a QR code covers the design side.
  • L rarely. It keeps the code smallest but leaves little room for scratches or ink spread.

5. Keep a four-module quiet zone

ISO/IEC 18004:2024 requires a clear margin, the quiet zone, at least four modules wide on every side. In the file, that means nothing inside that margin: no text, no frame, no background pattern, no trim line.

A simple check: measure one module, multiply by four, and draw a box that far out from the code. Anything inside the box has to go.

6. Colour: solid black on light stock

QR codes are designed to read as dark modules on a light background. For print, that means:

  • Use solid black where you can. A single black ink gives crisp edges. Rich black, a black built from several inks, can look deeper on large areas. On small detail such as QR modules, any slight misalignment between inks can leave coloured fringes. Ask your printer which they recommend for fine detail.
  • Use light, plain stock behind the code. White or a pale paper colour works best.
  • Put nothing behind the code. No gradients, photos, patterns or tints under the modules or the quiet zone.
  • Avoid pale or metallic inks for the code. They look elegant but give the camera too little contrast.

Light-on-dark codes are a special case. Our guide to QR codes on metal, PVC and bamboo cards covers how they behave on darker finishes.

7. Bleed, trim and safe area

Printers trim cards from a larger sheet, and the cut is never perfect. So:

  • Bleed: extend background colour beyond the trim line by the amount your printer asks for.
  • Trim: expect the cut to wander slightly.
  • Safe area: keep the code and its full quiet zone well inside the trim, away from rounded corners.

If you use our online designer, it shows a red bleed area and a green safe zone on the card. Keep the code and its margin inside the green line.

8. Proof checks before you approve

Read the proof as a checklist:

  1. The code opens the right profile.
  2. The code is the size you planned, not scaled down to fit.
  3. The quiet zone is clear on all four sides.
  4. The code is solid and dark on a light background.
  5. Nothing overlaps the code: no text, icon or fold.
  6. The code sits inside the safe area.
  7. Names, numbers and spelling are correct.

9. Test-scan on three or more phones

Never approve a full run from a screen. Print a proof at real size, ideally on the same stock, and run this routine:

  1. Use at least three phones: an iPhone, a Samsung or other Android phone, and one older phone if you have it.
  2. Scan with the built-in camera in normal light.
  3. Scan again in dim light, like a hotel bar or event hall.
  4. Scan close up and at arm's length.
  5. Tilt the card slightly and scan once more.
  6. Each time, check that the profile opens and Save contact works.

If any scan fails, fix the file and test again. Our guide to a QR code business card that is not scanning matches each symptom to its cause.

When you order from us

Our QR code business cards carry a dynamic QR code, so the code holds a short link and stays small. You can upload your own artwork or use the online designer with its bleed and safe-zone guides. Once the cards arrive, our practical guide to using QR codes on business cards covers what to print beside the code and how to hand it over. More guides are on the blog.

Frequently asked questions

A vector format: SVG, a vector PDF or EPS. It keeps every module sharp at any size. Use PNG only at final size, and avoid JPEG.

There is no business-card rule in ISO/IEC 18004:2024. GS1's retail range of 0.396 mm to 0.990 mm per module is a sensible floor. With a short link, that gives a code of roughly 15 to 18 mm including the quiet zone. Bigger is safer.

M for most cards on smooth stock. Q for textured or engraved surfaces. H only if you add a small logo in the centre.

For fine detail like QR modules, a single solid black usually prints sharper. Ask your printer, because their press setup decides the answer.

No. Keep the code and its four-module quiet zone inside the safe area, well away from the trim and rounded corners.

At least three, including an iPhone and an Android phone. Test in normal and dim light, close up and at arm's length.

Related guides

View All

Ready to Upgrade Your Networking?

Get your premium QR business card and start making lasting first impressions.

Shop the Full Range